Drop down feeding system
The Sinking Feeding System can accommodate a wide variety of products delivered in rows from your processing line, including:Swiss roll, Layer cake , Cupcake, Chocolate coated wafer, Sponge cake, Soft cakes, Energy bars, Nutrition bars and so on.
Introduction
2. This system includes main feeding unit, sinking feeding unit, transition feeding unit, automatic feeding unit, control system and packing machine, through the sensor detecting to control automatic feeding unit to achieve continuous production, low rejection rate and nice packaging affect.
3. This system can accommodate a wide variety of products delivered in rows from processing line and automatically distributes up to several thousand products per minute to various individual packaging machines to achieve no worker contact and interference with high efficiency.
Maintenance and inspection
(1) Clean the machine each time after packaging.
(2) Turn off the power before cleaning the machine to low the temperature of heating part.
(3) Never spray the water or steam directly on the machine when cleaning.
(4) Main components to be cleaned:
b.Brush off the film chips adhered to the sealing surface by the wire brush applied with the silicone oil.
c.Clear the dirt on the control panel, safety cover and operating surface by a piece of soft cloth.
dConductive ring of the mid sealing tool and end sealers: clean it once a week or two weeks. Clean the conductive ring by the back of the sandpaper with the master power off.
2.Maintenance and clean for machine every month.
(1) Apply the lubricating grease on the bearing of the end sealers.
(2) Apply the lubricating grease on the gear and chain (pulley) of the driving unit.
(3) Check the tightness of the chain and belt of the driving unit, and tighten the loosed one.
(4) Check the tightness of the fastening screw or nut of all parts, and tighten the loosed one.
(1) Check the wear intensity of the belt of the driving unit, and replace the worn-out one.
(2) Check the wear intensity of the rubber roller, and replace the one affecting the film advancing effect.
(3) Properly adjust the brake unit of the film-carrying roller.
(4) Check all wearing parts, and immediately replace the damaged one.
(5) Check the fastness of the wiring on the electrical terminal plate, and tighten the loosed one. Check the inverter, programmable controller and circuit board, and remove the dust or dirt on them by the compressed air.
(1) Clean the machine each time after packaging.
(2) Turn off the power before cleaning the machine to low the temperature of heating part.
(3) Never spray the water or steam directly on the machine when cleaning.
(4) Main components to be cleaned:
b.Brush off the film chips adhered to the sealing surface by the wire brush applied with the silicone oil.
c.Clear the dirt on the control panel, safety cover and operating surface by a piece of soft cloth.
d.Conductive ring of the mid sealing tool and end sealers: clean it once a week or two weeks. Clean the conductive ring by the back of the sandpaper with the master power off.
5.Maintenance and clean for machine every month.
(1) Apply the lubricating grease on the bearing of the end sealers.
(2) Apply the lubricating grease on the gear and chain (pulley) of the driving unit.
(3) Check the tightness of the chain and belt of the driving unit, and tighten the loosed one.
(4) Check the tightness of the fastening screw or nut of all parts, and tighten the loosed one.
(1) Check the wear intensity of the belt of the driving unit, and replace the worn-out one.
(2) Check the wear intensity of the rubber roller, and replace the one affecting the film advancing effect.
(3) Properly adjust the brake unit of the film-carrying roller.
(4) Check all wearing parts, and immediately replace the damaged one.
(5) Check the fastness of the wiring on the electrical terminal plate, and tighten the loosed one. Check the inverter, programmable controller and circuit board, and remove the dust or dirt on them by the compressed air.
FAQ
Q1: What type of professional automatic packaging system do you have?
Answer: Our custom-made automatic packaging system is usually equipped with horizontal packaging machine or vertical packing machine that use packaging film, cartoning machine, case palletizers, etc.
Q2: I'm worried that I don't know how to operate your machin
Answer: Do not worry. Our top quality automatic packaging system is servo controlled, which greatly simplifies the difficulty of operation and commissioning. Most of the daily operation of the machine can be conducted by a few start-stop buttons and HMI. If you have different products or packages that need to be changed, we can provide instructional videos to give you step-by-step tutorial. Also, the HMI has memory function, which is convenient for you to reload the settings in the future.
Q3: If I buy your biscuits automatic packaging system, what technical support can I get?
Answer: Whether buying any bakery automatic packaging system, including cookies automatic packaging system and bread automatic packaging system, we will provide you with 24-hour online technical support. In addition, we can also provide you with instructional videos on the installation and daily commissioning and maintenance. For some customized automatic packing system, our professional after-sales technicians can also provide on-site installation and commissioning services as per request (buyer should bear the cost for the service).
Q4: How do we build trust in the first business?
Answer: We believe that a win-win business must be based on our professional services and excellent products. Our team will fully study your needs, and clearly explain our products and solutions to you so that you can understand our services. We can take you to visit our modern factory through a video call, so that you can understand how your machine will be produced and let you know more about our products. Before delivery, we can cooperate with your partners to carry out factory acceptance test, or carry out acceptance through test video or video call. Make sure that the best automatic packaging system you need is ready before shipment.
Q5: How can I find the suitable automatic packaging system I need?
Answer: We will fully communicate of the information of your products, packaging scheme, and feeding method. We have nearly 30 years of experience as a automatic packaging system manufacturer and can provide you with similar case videos for your reference. If necessary, we will ask you for samples of products and packaging films for testing, in order to find the most suitable and cost-effective solution for you.
| Model | Drop down feeding system |
| Main feeding unit | 1000/1200 mm |
| Belt width | Depended on actual project |
| Feeding speed | Depended on actual project |
| Packing speed | 35-150 bags/min. (For one machine) |
| General power | Depended on actual project |
| Motor power | Depended on actual project |
| Noise | ≤78 db |
| Power supply type | 1Ph. 220V 50Hz |
